Ready to haul out

Blue Mistress has moved out of the marina onto a trot mooring and will be hauled out next week.

Pre-refit 2007

The image is a good study in comparative yacht design. (Blue Mistress is the boat in the middle if this is the first time you’ve seen this blog).

Everything has been taken out of her, except flares, warps and fenders and an anchor on the foredeck.

It’s interesting to see she is a little down at the stern. This is the inboard engine which was added later.

She originally had a large outboard on the stern which must have weighed her down further.

She sails better with weight forward.

This is a major refit, which is planned to take six weeks or so. Among other things, all the deck fittings are coming off and being refitted and the deck recoated. There are some annoying leaks on some of the fittings and, rather than only seal those and wait for others to open up, we are “starting again”

Fittings missing from the coach roof are grab rails.

DSCF5454

When I stripped the lining from the cabin deckhead, I discovered the original holes for the grab-rail fittings which have been filled in. My natural inclination is to replace them – safety being the most obvious reason, but I don’t know what the best design would be. Elegant carved teak is not the Blue Mistress style. What are the alternatives?

 

The Cockpit Sole

One of the problems with the Folksong is cockpit drainage.

Cockpit Detail

There are two drains set into the aft end of the cockpit that, in Blue Mistress’ case, lead out below the waterline.
Because the cockpit sole is at water level, there is always water visible in these drains.
At no time, in the six months I have sailed her, have I got wet feet, or found there to be any other than a minimal amount of water around these drains.
I am assured by the previous owner that he found this to be so too.

However, I know of at least one other boat that has ‘wet foot’ problems.

Well, I have found that the cockpit sole of Blue Mistress is a false one. It is 4-5 inches above the original.
There is a space between with, I presume, a supporting framework.
I guess this was a problem picked up when she was originally launched.

The real problem, of course, is how to placing sea valves on the outboard end of the drains to stop inflow in the unfortunate event of the drain becoming detached.

One solution is to place a sealed box containing an automatic pump below the cockpit, and direct the drains into this with an outlet above the waterline.
It sounds plausible, but a) expensive, and b) likely to be a drain on the batteries.

The jury is still out.

Inshore Craft 1

“We treat the past as a foreign country, when, in reality, it was occupied by the same people as us.”

I’ve forgotten who said that but I was reminded of it when I saw that Edgar March’s “Inshore Craft of Britain: In the Days of Sail and Oar” has just been republished.

It was first published in 1970, and covers small working boats of the Nineteenth and early Twentieth Centuries. Reading it, I was fascinated that an island as small Britain should have developed so many different shaped boats to perform more or less the same thing. Each locality had grown a different tradition. These working boats were, in effect, visual versions of regional accents. Thirty five years later, I am still fascinated.

Three reasons for liking this book:

1. For the boats themselves – as complex objects, with lines and detail, some more elegant than others, but all with a functional beauty that fitted their surroundings.

2. They were true examples of the the concept of ‘form following function’, made more substantial in that they were the livelihood of their owners and crew. Here were small boats constructed in local yards round the coastline of a small island. They varied in shape, in design and in size, not just from region to region but often from harbour to harbour, the only limitation being in the wood and materials used in their construction.

On the face of it, looking back from our mass-produced, communication-efficient world, it can be difficult to understand why this Falmouth Workboat, photographed off Polruan in Cornwall 

Falmouth Quay Punt

should differ so much from this Coble, photographed at Seahouses in Northumberland.

sea 062

After all, they were built for more or less the same purpose.

In fact, the answer isn’t so difficult. Take one island, facing north, south, east and west; take tides, currents, prevailing winds; take a long, varied coastline, some stretches steep and rugged, some shallow with sand and mud, some exposed to the weather, some with large safe deep harbours, some with just a rock or two for shelter. Add a function – fishing, trade, piloting, transport.

Even today, these factors would make a difference to shape and form, but think what centuries of experience of local conditions would do. Think about the materials that would be available in one part of the country that weren’t in another. Think about the traditions that would have grown up around a particular coastline. And to really understand what it was like, you need to take one other factor into account:

3. The owners and crew who sailed in them. They represented the way of life of countless small communities. This was a world where experience counted, where fathers passed their skills onto their sons and, less so in those days, their daughters. Here were local communities, not necessarily isolated from one another but certainly separated, who developed their own craft specifically for the coastal conditions in their area.

No different from us today – they faced the problems of the time and had to solve them. They laughed like us, they cried like us, they succeeded, they failed, they loved, they hated – just like us. They knew what hard work meant. Some did it well, some badly, a few brilliantly. Some were successful financially and went on to do more, some were less so. But their knowledge, skills and attitudes came from doing, from experiencing first-hand. It took longer to gain them, but the best results lasted as long, if not longer, than ours will today. Those hard-won abilities created individuals in a world that needed individuals.

There is one major difference between are ancestors and us today. We have access to more knowledge and more skills, and at a far younger age, than those who came before us could possibly imagine in their wildest dreams – (think Google, endless courses, books, journals and DVDs). But, despite this, our basic ability to absorb and use our new-found knowledge has not grown in line with our sources. In the end, we learn best by doing too – and it still takes time. All the rest of the stuff that comes our way is ‘on approval’ – and we are becoming increasingly swamped by it, struggling to be individuals in a sea of often irrelevant information.

So what’s your point, Bill?

I don’t have a romantic view of the past but I do have a respect for those who learn from experience – and I don’t care whether they were born in 2007 or 1007. (At this point, it would be easy to bang on about our not learning the lessons of the past, but that’s for others to do).

What I would like to do is to stay with boats and to use the concepts above – a) boats themselves, b) the fact of their form following their function, and c) the crews who sail in them, and, as I travel around the coasts not just of the UK but further afield, record, if I can, examples of craft that are being used today that represent this long line of experience. No doubt, some will exhibit a high quality of craftsmanship, some less so. But it isn’t the quality I want to pick out here. What interests me are the solutions to maritime problems that work in particular circumstances. Like this small fishing boat moored in Trikeri on the Pelion Peninsular, on the Aegean shores of Greece.

DSC00628

I do not pretend to be an expert. Inevitably, my efforts will be random observations and certainly not comprehensive. But, this is not an academic study, it is a record of small pleasures, pleasures I believe I share with many other people.

It is also a record of concern, a concern I also share with many others. Times are changing so fast that much hard-won, long-term experience is being sacrificed in the name of easily-found, short-term expediency. We badly need to hang on to some of that experience.

So, my entries to this blog over the next year or so will include an ‘Inshore Craft’ series of images. I hope they will be of interest to you. Please feel free to add your own if you wish.

 

Where to move the socket

So here’s a problem to solve?

Autohelm socket

This is where the Tiller Pilot plugs in – (Raytheon ST1000 plus)

It’s in the corner – (currently, dirty corner following heavy rain), of the cockpit, out of the way, or, at least whoever placed it there thought so.

It’s not the socket, of course, that’s the problem, it’s the cable that plugs into it.

I knock it far too often – usually during manouvering, sometimes just feeling expansive and leaning back, occasionally I have put something on it without thinking. Mostly I don’t notice myself doing it – too busy concentrating.

The result is a disconnected self-steering which becomes evident sooner rather than later, depending on which direction we are pointing.

So I need to do something apart from scrubbing the deck. The socket either needs to be protected, or moved – but where? especially as there is no nearby vertical surface to attach it to.

I’m sure there’s a good solution out there somewhere.

 

Boom Outhauls – a query

I went down to the boat last week to run the engine for a while and check out the jobs we are going to do when she comes out of the water in March. A quiet couple of hours messing about in a boat – is there anything better?

The engine started first go and settled into a friendly rhythm. The no.1 battery was low again but charged up ok.

We are going to tackle a whole range of jobs from reseating deck fittings to replacing the hatches on the stern lockers.

There’s a design problem with the stern lockers – water gets in far too easily. Having played with ideas of rubber seals on the hatches themselves and also around the opening, I’ve gone for the more expensive, but more robust and long-lasting grp option, on the lines of the ones in the image below.

DSCF5347

I’m not over keen on the wooden embellishment, but the hatch lids are tight fitting, and, at the same time, can be accessed easily. They can be removed completely so I’m not banging my head or having to hold them open. They are permanently attached to the boat by a length of rope long enough to allow temporary stowage in the cockpit, or on the adjacent lid, or made fast to the pushpit. They can also be tied down in a sea.

The rigging needs some attention too. Contemplating the setup, and how she sailed during the summer, it struck me that there were one or two points I’d failed on. I am sure I can get her sailing better.

One of these is/are the boom outhaul/s, below, not currently rigged.

Outhauls

I would be interested to hear how other people set them up and manage them under sail. There seems to be plenty of room for adjustment – but in which direction?

12 reasons to spend money on the boat

I woke up this morning with a wild debate raging between my ears.

I am in a position that I guess most boat owners find themselves at some stage.
Can I justify spending a substantial amount of money on my boat, when the one certainty is that there will be little, (probably no), financial return on the investment?

The argument is running like this:

As this is a leisure activity, should I be looking beyond a gain in financial capital.
Surely, there are gains in human capital and social capital that are more relevant and definitely worth seeking.

So my current reasons for spending the money are sketched out below in personal and social terms :

Twelve reasons to spend money on Blue Mistress:

  1. To be able to continue to enjoy sailing for the sake of it.
  2. To restore and give longer life to an attractive, sea-kindly vessel that can be passed on to a younger owner when I can no longer sail.
  3. This boat has a design, shape and size that make it ideal for single-handed sailing, and, given that we won’t be living aboard,  for the two of us to spend time together comfortably.
  4. To have a specific activity that we can enjoy together as a complete family – the not-so-young children can be involved too. On the occasions we are together, we can learn together.
  5. To be able to take friends out for a day/morning/afternoon – to enjoy sailing in good company.
  6. To be able to explore the coastline and harbours of Devon and Cornwall.
  7. To open up the possibility of going further afield – around the UK coastline, across to France, or to Ireland.
  8. For personal health – fresh air, exercise, mental stimulation outside a daily career.
  9. To have an activity that will take me out of that career and onto the next stage, whatever that may hold. Since I bought Blue Mistress, I am meeting interesting, active, concerned people in situations that would never have happened if I had maintained the status quo.
  10. The boat and the maritime environment give me a focus for my writing and photography. For me this is the more outward-looking contribution.
  11. In environmental terms, from a maritime perspective, I can witness first hand the effects of global warming.
  12. Sailing, harnessing energy from the wind and the sea, is essentially a green activity, and worth pursuing because of this. As with most similar activities, it is not quite as simple as it first appears – some aspects are more ‘green’ than others and, no doubt, these will be the source of debate over the next decade. How can we learn about them without being involved in them?

The trick seems to be in avoiding sending good money after bad money.
If I get it right, although I will have invested more initially, I will have lifted the value of my boat just a little in financial terms, but a lot in human and social terms, ensuring longer-term enjoyment and making possible the outcomes I am looking for.
If I get it wrong, I will have spent albeit less money, but on short-term improvements that are likely to beget more short-term improvements that, in the long-term will cost me a lot more both financially and in personal angst, and will lead to me and my boat parting company sooner rather than later.

You can see which way the argument is going, can’t you.

The entrance to Bude Haven

DSCF5318

This the Barrel Rock at the entrance to Bude Haven, North Cornwall at 1445 this afternoon.

DSCF5331

High water was 1334, the wind is south west, force 6-7.

The entrance to Bude Haven January 2007

This coast stretches North-South. Due west is Newfoundland, Canada.

This is not a coast for a small boat on a day like today, but there was a time when the choices were different.

Entering Bude through the surf

This is one of a number of posts on the Ketch “Ceres”. They have been presented in a random order as and when I have found, or been given, new material. They represent steps in a personal quest to find out more about one branch of my family.

If you are interested in maritime history or would like to read more, please use the Search facility at the top right hand side of this page (‘Ceres’). If this is not available on your current screen, then click on ‘Bill’s Boat Blog’ – (or the title of this entry, then ‘Bill’s Boat Blog’), to be taken to the correct page.

New phase in the Blue Mistress story

Today marked a new phase in the Blue Mistress story.

It was time to decide on exactly what the spring refit will involve – jobs, time, costs.

Richard from the boatyard came and helped move us forward – very diplomatically I thought, although he needn’t have been. We agree where we are going with the boat, we just needed to agree the process of getting there.

Waiting for refit - January 07

Basically, we have to ensure the deck is watertight before we can do anything below. So this will be the focus for 2007.

It will involve removing all the deck fittings, including some recent ones, reseating them, replacing and making watertight the lazarette hatch covers, replacing the window ports, repairing grp, stripping and recoating the deck. The mast will be removed and the rigging checked.

She is booked to come out of the water and placed under cover in March, and will need to be dried out (with dehumidifiers) first.

DSC05295

That’s all I’m going to say on the subject for while. It’s grit your teeth and cross your fingers time.

Boat Blog – Second Phase

What did it take to keep me writing?
One week and some encouragement from the other side of the world.

What is it they say?
‘Praise’ is the greatest form of motivation?
Certainly worked for me.

This marks a new phase in the Boat Blog
My purpose has changed a little and we shall see how it develops.
More on this later.

Refit under way – end of blog

Summer mooring

This is the last entry in this blog.

I started it three months ago as a way of finding out more about Folksong 25s.
The idea was to create a contact point – (throw out a line).
Anyone could place a comment on any of the entries and that comment would arrive in my inbox almost instantly.

Three months on, a number of people have kindly contacted me and been extremely helpful and informative.
I would like to thank them.
I have the information I was looking for and I hope to continue these contacts over time.

I am old enough to be totally amazed at the power of this medium.
Imagine, even five years ago, having the ability to search across continents to find out information that is relevant to only a very few?

A letter to Practical Boat Owner might have got a result, but the message would have appeared only once and, even if it had been picked up, would have required much more energy from those wishing to reply.

With the blog, I have a small body of work that will remain on the internet for another nine months or so.
I am keen to see whether others follow it up.
.
Blogs – and I’ve read a lot of them, seem to me to be mostly more useful to the writer than the reader.
They are an opportunity for the writer to state his/her point of view.
Sometimes they’re informative, sometimes expressive, often plain dull.

For me, it has been a short journal.
To ‘spread the net’, I have done more than concentrate on the boat alone and I hope the writing has been of passing interest.

Snug for the winter

As for Blue Mistress, the first steps of the refit are underway.
Yesterday afternoon, there was a definite sense of direction on board.
Perhaps I shall come back later in the year with an update.

In the meantime, enjoy your sailing

Bill